Cisco 200-301 Dumps - The Sure Way To Pass Exam
200-301 Exam Questions (Updated 2026) 100% Real Question Answers
NEW QUESTION # 721
What is a characteristic of an SSID in wireless networks?
- A. broadcasts a beacon signal to announce its presence by default
- B. eliminates network piggybacking
- C. must include a combination of letters and numbers
- D. prompts a user for a login ID
Answer: A
Explanation:
SSID broadcast a beacon message periodically & stations listen for these messages from the AP,
& it's called passive scanning, active scanning probe request & probe response.
NEW QUESTION # 722
Refer to the exhibit.
What is the next hop address for traffic that is destined to host 10.0.1.5?
- A. 10.0.1.4
- B. 10.0.1.50
- C. 10.0.1.3
- D. Loopback D
Answer: B
NEW QUESTION # 723
Refer to the exhibit.
What is the next hop address for traffic that is destined to host 10.0.1.5?
- A. 10.0.1.4
- B. 10.0.1.50
- C. 10.0.1.3
- D. Loopback D
Answer: B
NEW QUESTION # 724
Refer to Exhibit.
The loopback1 interface of the Atlanta router must reach the loopback3 interface of the Washington router.
Which two static host routes must be configured on the NEW York router? (Choose two)
- A. ipv6 route 2000::1/128 2012::1
- B. ipv6 route 2000::3/128 2023::3
- C. ipv6 route 2000::3/128 s0/0/0
- D. ipv6 route 2000::1/128 2012::2
- E. ipv6 route 2000::1/128 s0/0/1
Answer: A,B
NEW QUESTION # 725
Drag and Drop Question
Drag and drop the network protocols from the left onto the correct transport services on the right.
Answer:
Explanation:
NEW QUESTION # 726
Drag and drop the management connection types from the left onto the definitions on the right.
Answer:
Explanation:
Explanation:
NEW QUESTION # 727
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2.
Based on the information in the graphic, what is the cause of this problem?
- A. The priority on R1 should be set higher.
- B. A backup designated router needs to be added to the network.
- C. The cost on R1 should be set higher.
- D. The OSPF area is not configured properly.
- E. The hello and dead timers are not configured properly.
- F. The OSPF process ID numbers must match.
Answer: E
NEW QUESTION # 728
An engineer must configure a core router with a floating static default route to the backup router at 10.200.0.2.
Answer:
Explanation:
Explanation:
NEW QUESTION # 729
Drag and drop the configuration management terms from the left onto the descriptions on the right. Not all terms are used.
Answer:
Explanation:
NEW QUESTION # 730
Drag and drop the descriptions of file-transfer protocols from the left onto the correct protocols on the right.
Answer:
Explanation:
Explanation:
NEW QUESTION # 731
Which benefit does controller-based networking provide versus traditional networking?
- A. combines control and data plane functionality on a single device to minimize latency
- B. allows configuration and monitoring of the network from one centralized port
- C. moves from a two-tier to a three-tier network architecture to provide maximum redundancy
- D. provides an added layer of security to protect from DDoS attacks
Answer: B
NEW QUESTION # 732
Refer to the exhibit.
IP connectivity and OSPF are preconfigured on all devices where necessary. Do not make any changes to the IP addressing or OSPF. The company policy uses connected interfaces and next hops when configuring static routes except for load balancing or redundancy without floating static. Connectivity must be established between subnet 172.20.20.128/25 on the Internet and the LAN at 192.168.0.0/24 connected to SW1:
1. Configure reachability to the switch SW1 LAN subnet in router R2.
2. Configure default reachability to the Internet subnet in router R1.
3. Configure a single static route in router R2 to reach to the Internet subnet considering both redundant links between routers R1 and R2. A default route is NOT allowed in router R2.
4. Configure a static route in router R1 toward the switch SW1 LAN subnet where the primary link must be through Ethernet0/1. and the backup link must be through Ethernet0/2 using a floating route. Use the minimal administrative distance value when required.
Answer:
Explanation:
Answer as below configuration:
On R2:
Enable
Conf t
Ip route 192.168.1.0 255.255.255.0 10.10.31.1
On R1:
Enable
Conf t
Ip route 0.0.0.0 0.0.0.0 10.10.13.3
On R2
Ip route 172.20.20.128 255.255.255.128 e0/2
Ip route 172.20.20.128 255.255.255.128 e0/1
On R1
Ip route 192.168.0.0 255.255.255.0 e0/1
Ip route 192.168.0.0 255.255.255.0 10.10.12.2 3
Save all configurations after every router from anyone of these command Do wr Or Copy run start
NEW QUESTION # 733
Drag and drop the elements of a security program from the left onto the corresponding descriptions on the right.
Answer:
Explanation:
Explanation:
https://www.ciscopress.com/articles/article.asp?p=1998559&seqNum=3
NEW QUESTION # 734
Which switch would STP choose to become the root bridge in the selection process?
- A. 32769: 22-33-44-55-66-78
- B. 32768: 11-22-33-44-55-66
- C. 32768: 22-33-44-55-66-77
- D. 32769: 11-22-33-44-55-65
Answer: B
NEW QUESTION # 735
Drag and drop the statement about networking from the left into the Corresponding networking types on the right. Not all statements are used.
Answer:
Explanation:
Explanation:
2, 4
1, 3
NEW QUESTION # 736
......
Pass Cisco 200-301 Exam Quickly With DumpsMaterials: https://braindumps2go.dumpsmaterials.com/200-301-real-torrent.html
